AC Contactor Sizing Chart: HP, FLA & Voltage | SIMPLYBUY
海报

AC Contactor Sizing Chart: Match Motor HP, FLA, Voltage and Utilization Category

October 9, 2026

Quick Answer: A contactor sizing chart is a shortlist tool, not a universal cross-brand answer. Start with the motor nameplate: record full-load current (FLA), voltage and phase, then match those figures to one manufacturer’s AC-3 rating for normal motor duty. Horsepower helps you find the right table row, but the exact catalog number confirms the coil, auxiliary contacts and mounting. SIMPLYBUY is a multi-brand electrical automation distributor and supply-chain integration platform, so we can review those details across a mixed-brand BOM before you order.

This guide is for buyers who need to price or replace a contactor without turning the job into a panel-design project. You will learn how to read a contactor sizing chart, find a starting size for a 20 HP motor, distinguish AC-1 from AC-3 duty, and prepare a quote request that avoids common model-suffix errors. For basic product terms, see our guide to AC contactors.

What Does a Contactor Sizing Chart Actually Tell You?

A contactor sizing chart links a motor’s horsepower or kW and system voltage to a manufacturer’s contactor frame or catalog number. It applies only to that product line and the listed conditions.

What does FLA mean?

FLA stands for full-load amperes, the current a motor draws at its rated load and voltage. The contactor carries that current, so FLA matters more than horsepower alone. Use the nameplate first. If it is missing, UL 508A Table 50.1 is a common North American fallback:

Motor HPApprox. FLA at 230 VApprox. FLA at 460 V
515.2 A7.6 A
1028 A14 A
1542 A21 A
2054 A27 A
3080 A40 A
50130 A65 A

These values are planning aids based on UL 508A Table 50.1. The nameplate takes priority, especially for low-speed or multi-speed motors. IEC charts commonly use kW rather than HP, so read the unit before choosing a row.

Does contactor size change with voltage?

Yes. The same 20 HP motor draws about 27 A at 460 V but about 54 A at 230 V. A device selected for the 460 V figure is too small for the 230 V circuit, even though the horsepower label is identical. Always quote horsepower or kW together with voltage and phase.

How Do You Size an AC Contactor Step by Step?

Use this sequence when comparing catalog options:

  1. Record the motor data. Capture FLA, voltage, phase, frequency and the application’s normal starting pattern.
  2. Choose the utilization category. Use AC-3 for ordinary squirrel-cage motor switching. Use AC-4 for frequent jogging, inching or plugging.
  3. Shortlist a frame in one brand’s chart. Match the exact voltage and category, then confirm that the contactor’s AC-3 current is at least the motor FLA.
  4. Set the coil separately. The coil voltage and frequency come from the control circuit, often 24 V AC, 110-120 V AC or 220-240 V AC. The coil code changes the part number, not the load rating.
  5. Confirm the physical configuration. Check pole count, NO/NC auxiliary contacts, terminal type, mounting, enclosure and ambient conditions.

Do not use thermal current (Ith) as a substitute for the AC-3 switching rating. Ith describes continuous heat capacity under stated conditions, not motor-switching duty. The AC contactor product range is a useful place to compare families after these inputs are fixed.

Motor contactor sizing guide shows an ABB AF116-30 contactor beside a Schneider TeSys LC1D65A contactor, with four steps for selecting contactors: Motor Nameplate FLA, Voltage, AC-3 Rating, and Coil.

What Size Contactor Do You Need for a 20 HP Motor?

Assume a 20 HP, 460 V, three-phase motor with a nameplate FLA of 27 A, normal AC-3 starting and a 220 V AC control circuit. Your shortlist target is an AC-3 contactor rated at or above 27 A at 460 V.

The Schneider Electric LC1D65AM7C is a 65 A AC-3, three-pole contactor with a 220 V AC coil. It covers this example load but may not be the most economical frame; the brand chart may offer a closer rating.

At 230 V, the same 20 HP motor needs a frame sized for roughly 54 A, not 27 A. Overload protection is a separate decision based on the same FLA. See our guide to calculating overload relay size before assembling the full starter.

Which Utilization Category Should You Use: AC-1, AC-3 or AC-4?

The utilization category describes the switching duty the contactor was tested for. It is not a quality grade.

CategoryTypical load and dutyWhat buyers should check
AC-1Non-inductive or slightly inductive loads, such as resistance heatingOften the highest current rating on a frame, but not the motor-starting rating
AC-3Squirrel-cage motors started and switched off while runningThe normal default for pumps, fans, compressors and conveyors
AC-4Squirrel-cage motors that are inched, plugged or frequently joggedLower published rating and faster contact wear than AC-3

AC-3 is the category to use for ordinary motor duty. If the machine reverses, jogs or plugs often, compare AC-4 ratings and expected contact life before choosing a frame. Do not compare an AC-1 ampere number with an AC-3 ampere number. The IEC contactor application guide explains the categories and shows why the same device can carry different ratings.

Can You Use the Same Contactor Rating Across Brands?

No. A contactor sizing chart belongs to one manufacturer’s catalog, and each brand publishes its own frames, test conditions and accessory ranges. The same 30 kW, 400 V motor can land on different frame sizes from Schneider Electric, ABB and Siemens. Amperes may look similar while coil options, dimensions, terminal arrangements and price differ.

Use our industrial contactor brand comparison to understand the ranges, then verify the candidate against its own datasheet. For example, an ABB AF116-30-11-13 and the Schneider LC1D65AM7C can both cover some duties, but are not interchangeable without a full specification check.

What Should You Check Before Replacing or Quoting a Contactor?

Match the full model number, not just the amps or horsepower. Confirm:

  • Coil voltage, frequency and AC or DC type.
  • Number and type of main poles and auxiliary contacts.
  • Mounting, terminal and enclosure requirements.
  • Ambient temperature, altitude and any manufacturer derating.
  • Required datasheet, approval or traceability documents.
  • Quantity, destination and required delivery terms.

For a replacement, photograph the nameplate and terminal layout. If the original part is obsolete, treat the proposed alternative as a new selection. Our Allen-Bradley contactor replacement guide follows the same model-by-model approach. A contactor that hums, chatters or drops out may have a coil or control-circuit problem, so review contactor failure symptoms before ordering a replacement.

并排对比施耐德TeSys与ABB AF116-30接触器,列出线圈电压、负载类别、安装方式和完整型号后缀等核对项,并提示订阅前查阅各型号数据表。

How Can SIMPLYBUY Help You Confirm the Right Size?

SIMPLYBUY works with overseas traders, distributors, importers and project buyers across more than 100 brands and 300 suppliers. We do not manufacture contactors. Our role is to review your BOM, compare suitable catalog options, check model details and confirm the documents, availability and freight terms that apply to the quoted order. That is useful when a project combines a Schneider contactor, an ABB alternative and Siemens starters in one request.

What Is the Bottom Line?

Start with the motor nameplate, not the horsepower headline. Confirm FLA, voltage and phase, select the correct utilization category, then use one brand’s contactor sizing chart to shortlist a frame. The final order still needs the exact coil, auxiliary contacts, mounting and commercial terms.

Send SIMPLYBUY the brand, full part number or BOM, quantity and delivery destination. If a code is unclear, include a nameplate photo and the equipment model, and request a quotation with the required documents.

✕

Get A Quote

    ✕

    Download Catalog