--- title: "How to Test an Overload Relay: A Step-by-Step Guide for Troubleshooting" date: 2025-09-09T17:31:00Z modified: 2025-09-23T07:18:18Z permalink: "https://www.simplybuyglobal.com/blog/motor-control/overload-relay/how-to-test-overload-relay/" type: post status: publish excerpt: "" wpid: 3505 categories: - overload relay tags: - overload relay - ABB - Mitsubishi - Schneider featured_image: "https://www.simplybuyglobal.com/wp-content/uploads/2025/09/1b71c9d5-714a-4d68-b90c-44f7a5c59e79.webp" featured_image_alt: "How to Test an Overload Relay: A Step-by-Step Guide for Troubleshooting banner" timestamp: 2025-09-23T07:18:18Z --- You can test an overload relay by switching off the power, checking continuity with a multimeter, simulating an overload, and then resetting it. Taking these steps helps confirm the relay will trip when needed, [protecting motors from overheating](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/taxonomy/product_cat/motor-control.md) and preventing expensive downtime. Let’s take a closer look at what each step involves and the tools you’ll need to carry it out effectively. ## **Step 1: Gather Your Tools** ![Step 1: Gather Your Tools ](https://www.simplybuyglobal.com/wp-content/uploads/2025/09/fdf78eee-39a1-4e60-bbe4-791cb4fced7e.webp) Start by collecting what you’ll need for the test. A multimeter is the most important tool since it lets you check continuity and resistance. If you have access to an industrial relay tester, that’s even better because it allows you to simulate overloads more accurately. Do not forget basic protective gear such as gloves and goggles. ## **Step 2: Disconnect Power** ![Step 2: Disconnect Power](https://www.simplybuyglobal.com/wp-content/uploads/2025/09/19f305b2-8234-4dfa-93a0-31ac43e2ed97.webp) Before touching the relay, make sure the circuit is safe. Switch off the power supply to the motor and confirm that no voltage is present. Working on a live circuit puts both you and your equipment at risk, so this step is non-negotiable. ## **Step 3: Inspect the Relay** Take a close look at the relay. Burn marks, melted plastic, corroded terminals, or loose wiring are all warning signs. If you see obvious damage, testing won’t help. It is better to [replace the relay](https://www.simplybuyglobal.com/relay-supplier-for-all-types/) right away than risk a motor failure. ## **Step 4: Check Relay Using Multimeter** ![Step 4: Check Relay Using Multimeter ](https://www.simplybuyglobal.com/wp-content/uploads/2025/09/b0e848af-5f59-48dd-932c-042c1a8dc6b3-1.webp) Now you can move on to electrical testing. To check relay using multimeter: 1. Set your multimeter to resistance (Ω). 2. Place one probe on the input terminal (L1) and the other on the output terminal (T1). Repeat for L2–T2 and L3–T3. 3. A working relay shows continuity close to zero ohms. 4. If the meter reads infinite or “OL,” the relay is likely faulty. This simple step confirms whether the relay can still pass current properly. ## **Step 5: Simulate an Overload** ![Step 5: Simulate an Overload ](https://www.simplybuyglobal.com/wp-content/uploads/2025/09/89112565-1f5c-4f5c-a338-e6ced8cec77a.webp) The next step is to see if the relay will trip under stress. If you have an industrial relay tester, apply controlled current above the relay’s rated limit. Now watch closely; the relay should trip and disconnect the circuit as the current rises. Compare the trip point and time with the manufacturer’s specifications. If the relay fails to trip or trips inconsistently, it may need adjustment or replacement. ## **Step 6: Reset the Relay** After testing, bring the relay back to its normal state. - For manual models, press the [reset button ](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/post/automatic-vs-manual-reset-overload-relays.md)[o](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/post/automatic-vs-manual-reset-overload-relays.md)[n the front](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/post/automatic-vs-manual-reset-overload-relays.md). - For automatic models, allow time for cooling and the relay will reset on its own. Run one more continuity check to make sure the relay is ready to go. ## **When to Replace Your Overload Relay** [![](https://www.simplybuyglobal.com/wp-content/uploads/2025/09/8d0e9565-5534-486b-8384-a52bbd9d2cc7-1.png) ](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/taxonomy/product_cat/overload-relay.md) Even if a relay passes most checks, there are times when replacement is the safer and more reliable choice. - **Failed continuity**: If the relay shows no continuity during testing, it can no longer carry current and should be swapped immediately. - **Incorrect tripping**: A relay that trips too quickly or too late compared to its rating cannot properly protect your motor, putting your system at risk. - **Visible damage**: Burns, cracks, corrosion, or rattling parts are clear signs the relay is at the end of its life. Using counterfeit or low-quality relays risks inaccurate testing and unexpected failures. [Simply Buy](https://www.simplybuyglobal.com/) provides 100% [authentic overload relays](https://www.simplybuyglobal.com/relay-supplier-for-all-types/) from trusted global brands. With genuine parts, you can test with confidence and trust the results. ## **FAQs on Overload Relay Testing** ### **How to test a thermal overload relay?** [Thermal models](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/post/electronic-vs-thermal-overload-relay-schneider-guide.md) use a bimetal strip that bends under heat. To test: - Perform the continuity check with a multimeter. - Press the built-in test button if available to simulate excess current. - Confirm that the relay trips and the normally closed contacts open. ### **How to test overload relay refrigerator?** Overload relays in refrigerators protect compressor motors. To test: 1. Disconnect the relay from the compressor and power source. 2. Set your multimeter to ohms. 3. Check between the relay’s input and output pins. Continuity means it’s intact. 4. If there’s no reading or you hear rattling when shaking the relay, it should be replaced. ### **How to test ptc relay and overload protector?** Some refrigerators use a PTC relay with an overload protector. To test: - Measure resistance across the PTC relay. It should show moderate resistance, not zero and not infinite. - For the overload protector, check continuity. At room temperature it should be closed. If it reads open, replacement is required. [Get Free Quote](https://www.simplybuyglobal.com/contact/) ## **Conclusion** Now that you know how to test an overload relay, the next step is making sure you have authentic replacements on hand. At Simply Buy, every relay we supply is 100% original and globally certified. To support you beyond purchase, our after-sales services include: - **Technical consultation** to confirm compatibility and selection. - [**Troubleshooting help** if a relay fails](https://www.simplybuyglobal.com/wp-content/uploads/wp-mfa-exports/post/how-to-safely-reset-overload-relay.md) or trips unexpectedly. **Fast replacements** shipped from our global warehouses. With trusted brands and a verified supplier network, you can source overload relays confidently and keep your systems running without interruption. [Contact us today](https://www.simplybuyglobal.com/contact/). [![about Simply Buy motor controls, VFDs, and breakers—original, in-stock, and fast shipping.](https://www.simplybuyglobal.com/wp-content/uploads/2025/07/1752296239248-1200x596.webp) ](https://www.simplybuyglobal.com/)